环氧地坪的基础该如何处理？杭州赛卡地坪工程有限公司的技术转接周工为咱们整理了如下的方法供大家参考整理的方法

　　第一、用研磨机进行全面打磨。让破损、起沙、粘度不牢、开裂、空鼓之部位完全暴露出来;并将浮起的砂浆、旧环氧水泥结块等打磨平整。混凝土进行认真打磨，不能漏掉半点不打磨的地方，特别是很多强度不好的区域，一定要打磨到有强度的地方，否则，疏松的区域会随着涂层脱落，而且时间会很快，可能工程还没有结算就会脱掉;同时，建议打磨进行两道，两次呈十字交叉型，以防止有漏点，可以打磨得更加彻底。

　　第二、用研磨机进行全面打磨。让破损、起沙、粘度不牢、开裂、空鼓之部位完全暴露出来;并将浮起的砂浆、旧环氧水泥结块等打磨平整。打磨结束后，清扫完后，建议用吸尘器吸尘处理，以便涂料更好地渗透，水的张力大，容易影响渗透性;

　　第三、用研磨机进行全面打磨。让破损、起沙、粘度不牢、开裂、空鼓之部位完全暴露出来;并将浮起的砂浆、旧环氧水泥结块等打磨平整。对于没有伸缩缝的地面，要进行深切缝，以防止将来由于混凝土的内应力，形成不规则裂缝;有伸缩缝的地方，用钢筋钩进行清缝，然后用吸尘器进行吸尘。

　　第四、有不规则裂缝的地方，要进行切缝处理，用环氧砂浆进行修补，并注意修补的高低差;

　　第五、将处过的地面清洁。检验方法：经处理后，地坪表面平整、密实、干燥，无油污、且没有松动易碎颗粒，方可进行下一工序施工。伸缩缝、裂缝、空鼓地面、松动旧环氧的特殊处理

　　柱边和墙角边用角磨机进行角磨，处理的平整、平滑;

　　第六、有水的地方用吸水器把水处理掉，铲除表面的泥浆，然后用带水的洗地机洗地吸水，处理干净，晾一天，随后上底漆;

　　第七、有油污的地方，先把表面的油垢铲除干净，然后用清洗剂进行清洗，然后再用火烤，如果油污特别严重，需要敲掉混凝土重新浇筑。

　　Basic handling method of epoxy floor for company information

　　First, use the grinding machine for comprehensive grinding. Let damage, sand, viscosity is not firm, cracking, empty drum parts completely exposed; And the floating mortar, old epoxy cement agglomeration and other grinding smooth. Concrete should be carefully polished, not to miss any place that is not polished, especially many areas with poor strength, must be polished to the place with strength, otherwise, loose area will fall off with the coating, and time will be very fast, may not have the project settlement will take off; At the same time, it is recommended to carry out two grinding, two cross type, in order to prevent leakage point, can be more thorough grinding.

　　Second, use the grinder for full grinding. Let damage, sand, viscosity is not firm, cracking, empty drum parts completely exposed; And the floating mortar, old epoxy cement agglomeration and other grinding smooth. After the end of grinding, cleaning, it is recommended to vacuum treatment, so that the paint better penetration, water tension, easy to affect the permeability;

　　Third, the use of grinding machine for comprehensive grinding. Let damage, sand, viscosity is not firm, cracking, empty drum parts completely exposed; And the floating mortar, old epoxy cement agglomeration and other grinding smooth. For the ground without expansion joints, deep joints should be carried out to prevent irregular cracks caused by the internal stress of concrete in the future. The place that has telescopic seam, undertake clear seam with rebar hook, have vacuum cleaner next.

　　Fourth, where there are irregular cracks, it is necessary to conduct slit treatment, repair with epoxy mortar, and pay attention to the difference between the high and low repair;

　　Fifth, the floor will be clean. Inspection method: after the treatment, the floor surface is flat, dense, dry, no oil, and no loose fragile particles, before the next process of construction. Special treatment of expansion joints, cracks, empty drum floor and loose old epoxy

　　Column edge and corner edge Angle grinding machine Angle grinding, processing of the smooth, smooth;

　　Sixth, where there is water, use a water absorber to treat the water, remove the mud on the surface, and then wash the ground with water to absorb water, clean treatment, drying for a day, then on the primer;

　　Seventh, where there is oil pollution, first the surface of the oil scale to eliminate clean, and then use cleaning agent for cleaning, and then use fire to bake, if the oil pollution is particularly serious, need to knock off the concrete pouring.